Answers to Tshoot Drill – WAN Interface Down

certskills
By certskills January 22, 2014 09:05

The #CCNA scenario begins with a working router triangle, using a single OSPF area. Then you shutdown a serial link. What changes with OSPF show command output? Show ip ospf neighbor? Show ip ospf interface brief? Show ip route? And on which routers? Today’s post points out the config changes and status changes visible in some of the common show commands.

Earlier posts in this series:

Problem Statement: WAN Interface Down Tshoot Drill

Review of the Problem Statement

Look at the previous post for a full description of the problem statement, including the initial configuration for the various devices. For quick reference, however… the problem begins with a working OSPF configuration on all three routers, with the topology and subnets shown in Figure 1.

Figure 1: Subnets and Topology for this Tshoot Drill

To create this drill, the lab then shuts down R2’s S0/0/0 interface. What happens?

First Question: Which Show Commands Should I Examine?

One key troubleshooting skill is to think of all the show commands relevant to a particular scenario. You should list those that you know should change because of the changes to the configuration, but also those that are related but do not change. The command output that doesn’t change can sometimes tell you something about a problem as well.

For this particular exercise, I would suggest show commands for a couple of topics. First, what commands show the changes in status on the ends of the serial link? Then, what commands show the resulting changes to OSPF. Finally, take a look at the IP routing table. The commands could include:

  • Show interfaces
  • Show ip interface brief
  • Show ip ospf interface brief
  • Show ip ospf
  • Show ip ospf neighbors
  • Show ip ospf database
  • Show ip route
  • Show ip route ospf

R2 Changes: Interface State

First off, R2’s interface state changes on R2’s shutdown interface, S0/0/0. But what actually changes in the show command output, on both R2, as well as R, which sits on the other end of the serial link?

The most obvious status exists on R2, where the shutdown command is added to S0/0/0. Example 1 shows the state as “administratively down” (meaning shutdown was used) in the show interfaces command; this same state (not shown) exists in the output of the show ip interface brief command output. Example R2 also shows a little common notice of the interface state, out on the far right in the show ip ospf interface brief command, which simply lists S0/0/0 as “DOWN”, making no distinction of the down state being administrative.

Example 1: R2’s S0/0/0 Interface State After the Change

 

In comparison, R3 has no awareness of the “administratively down” perspective, because R3’s interface (S0/0/1) is not shutdown. Instead, sees the physical link as down, so both the first and last interface status (per show interfaces) lists a state of “down”. Before R2 shutdown its S0/0/0 interface, this command listed a state of up for both status codes.

Example 2: R3’s Serial Interface on the Other End

 

Also, note that the show ip ospf interface brief command lists the same status of down, which basically matches the second of the two status codes for the interface.

R1 Non-Changes: OSPF Neighbors and Interfaces

R1 should not list any changes in OSPF command output in this particular drill. The serial link that fails sits between R2 and R3. R1’s two neighbor relationships, to R2 and R3, still work. The OSPF-enabled interfaces on R1 (as listed per show ip ospf interfaces) remains the same.

However, R1 does lose one IP route. The R2-R3 serial link itself, subnet 172.16.10.0/23, fails, so none of the three routers will list IPv4 routes for that subnet in the output of show ip route.

Example 3: R1’s show ip ospf neighbor After the Change

 

R2 Changes: OSPF Neighbors and What Else?

R2’s S0/0/0, which connects to R3, fails. R2’s OSPF neighbor relationship with R3 fails. What else changes in show command output?

Closing Questions

That’s enough analysis to whet your appetite. To close, consider these questions, and feel free to post your opinions and answers.

  1. R2’s S0/0/0, which connects to R3, fails. What happens to R2’s OSPF neighbor relationships, as shown with show ip ospf neighbor?
  2. What differences (if any) occur in the output of the show ip ospf interface brief command output?
  3. How many routes will be listed in R3’s show ip route ospf, as compared to what you saw in Example 2 for R1?

 

#CCNA Tshoot Drill: OSPF Hello Timer Changed
#CCNA Tshoot Drill: OSPF WAN Interface Down
certskills
By certskills January 22, 2014 09:05
Write a comment

No Comments

No Comments Yet!

Let me tell You a sad story ! There are no comments yet, but You can be first one to comment this article.

Write a comment
View comments

Write a comment

Comment; Identify w/ Social Media or Email

Subscribe

Subscribe to our mailing list and get interesting stuff and updates to your email inbox.

Search

Categories