Interpreting show stp (1) – Answers

certskills
By certskills January 26, 2018 09:05

Of all #CCNA topics in the ICND2 half of CCNA, Spanning Tree Protocol (STP) looms with more intimidation than most. As for Mastering STP verification, the process begins with mastering the show spanning-tree command. This latest sample question focuses on the first section of that command’s output, asking about two topics: is the local switch the root switch, and what does the port number in that first grouping of messages tell you about the network? Check out the original question, and then dive in here for the answer and some explanation.

Answer

B: Some other switch is the root

E: Port G0/1 is a port on the local switch

 

Explanation

First, note that the output shown with the question lists one section of the show spanning-tree command’s output, and does not include the 2nd and 3rd section. The first section describes facts related to the root switch, while the second section describes the local switch (that is, the switch that generated the output.) The third section shows a list of local interfaces with their STP port roles and states. So, to answer this question, you need to have mastered some of the facts found in that first section of output – you just can’t rely on the other sections (which would have been useful as well). The question requires you to trust the information in the first stanza of messages.

When issuing the show spanning-tree command on the root switch, the root switch claims to be the root, with a statement “This bridge is the root.” The output for the question does NOT list that line, so the absence of that line tells us, without question, that the local switch is not the root switch. That fact rules out two answers about which switches might be root and confirms that the local switch is not the root switch.

Figure 1: Absence of Note about the Local Switch Being Root

The second set of related answers ask about what the mention of “GigabitEthernet0/1” means. Again, from memory and earlier study, you should know that if the local switch is not the root switch, that:

  • As a non-root switch, the local switch has a root port, and a cost to reach the root
  • The show spanning-tree command lists those facts in the first stanza: facts about the local switch and its relationship to the root switch

As a result, you can know that the first message group’s mention of port GigabitEthernet0/1 is an interface on the local switch (SW4), namely the port used as its root port. That fact rules out two answers, and rules in the answer that restates that port G0/1 is on the local switch.

Figure 2: Location of Two Lines in First Stanza about Local Switch

 

Common Mistakes

As usual, let me give you a few more pointers about avoiding common mistakes on the exam. In this particular area of concern – that is, the narrow world of just the first section of output from show spanning-tree – keep an eye out for these items:

  • Looking for the absence of a line of output can be one of the most challenging kinds of details to notice when under pressure on the exam. When in lab, take the time to compare that first stanza of messages on the root switch versus a non-root, and help that difference sink in visually: the claim of being the root, versus the two lines about root cost and root port.
  • Another set of facts to memorize: on a non-root switch, as in this question, that first stanza lists the Bridge ID of the root, followed by the root cost and root port of the local switch. So, it’s not all about the root switch: it’s about the root switch plus the local switch’s facts related to the root switch.

 

 

Question: Interpreting show stp (1)
Q: Matching Port Numbers with ACLs 1
certskills
By certskills January 26, 2018 09:05
Write a comment

4 Comments

  1. Ruben January 26, 10:58

    Again, thank you for all of these little exercises. they refresh the memory and keep us on top of the game 🙂

    Reply to this comment
  2. Gian May 3, 20:42

    Hi Wendell. I am a little confused on the Port portion of the show spanning-tree output. I understand the (GigabitEthernet) part is the local port on the switch. What does the 2 mean?

    Reply to this comment
    • certskills Author May 16, 11:42

      Hi Gian,
      Cisco switches assign each port an internal port number. These are integer, usually beginning at 1. For IOS features for which they just need to identify the port, regardless of type (FastE, GigE, multi gig, etc), the feature can reference the integer port number. The 2 in the output was the internal port number as automatically assigned by that switch.

      EG, here’s output from a another 2960. Note the bottom of the output, with two interfaces listed. the “priority.port” column shows the port numbers of 12 and 25 having been assigned to those two interfaces:
      P1-S2#show spanning-tree

      VLAN0001
      Spanning tree enabled protocol ieee
      Root ID Priority 32769
      Address 1833.9d7b.0e80
      Cost 8
      Port 25 (GigabitEthernet0/1)
      Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

      Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
      Address 1833.9d7b.1380
      Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
      Aging Time 300 sec

      Interface Role Sts Cost Prio.Nbr Type
      ——————- —- — ——— ——– ——————————–
      Fa0/12 Desg FWD 19 128.12 P2p
      Gi0/1 Root FWD 4 128.25 P2p

      Hope this helps…
      Wendell

      Reply to this comment
View comments

Write a comment

Comment; Identify w/ Social Media or Email

Subscribe

Subscribe to our mailing list and get interesting stuff and updates to your email inbox.

Thank you for subscribing.

Something went wrong.

Search

Categories